Thanks for your visiting, for product details, competitive price or more items, welcome to contact Sophie directly. :)
3 Axis NEMA 34 Stepper Motor Driver Kit 1161oz.in & 400W 60V Power Supply & 5 Axis Breakout for CNC Router Lathe
Note: If you need the dual shaft stepper motor, please leave message to us after order , If no message left, we will ship the single shaft .
3 x MA860H Sumtor step motor drive 2ph 24~110VDC AC18-80V 2~7.8A
3 x 86BYG 2ph Hybrid stepper motor 86HS11860A4 L 118mm 4-lead 6A 8.2NM 1.8 degree
3 x Switching Power Supply 400W 60V 6.7A for CNC S-400-60
1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver (free offer)
1 x DB25 Parallel Cable & USB Power Cable ( please check pictures for details)
Shaft length: 37mm
Shaft Type: double-sided milling flat 1mm
Shaft diameter: 14mm. If you need keyway shaft, please write us to ship keyway shaft after order. The same price.
is customized : yes
holding torque: 8.2nm
current : 6A
certification: CCC,CE, ISO
step angle: 1.8degree
Electrical Properties (ambient temperature Tj = 25C pm):
Logic Signal Current
Pulse Input Frequency
Connector P1 Configurations:
Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J1 & J2). For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when+12V or +24V used. The same as DIR and ENA signals.
DIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,0-0.5V when DIR-LOW. Please note that motion direction is also related tomotor-driver wiring match. Exchanging the connection of ?two wires for a coilto the driver will reverse motion direction.
Enable signal: This signal is used for enabling/disabling the driver. High level(NPN control signal, PNP and Differential control signals are on the contrary,namely Low level for enabling.) for enabling the driver and low level fordisabling the driver. Usually left UNCONNECTED (ENABLED)
Connector P2 Configurations:
Power supply, 18~80 VDC or 24~110VDC, Including voltage fluctuation and EMF voltage.
Motor Phase A
Motor Phase B
Input voltage: AC110-230V (supports 110V has a pull switch)
Output voltage: DC60V 6.7A
Output Power: 400W
Size: 215 * 115 * 50MM
5 axis CNC Breakout Board:
High performance, cost-effective.
Maximum support 5-axis stepper motor driver controllers.
Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
USB power supply and peripherals powered phase are separated to protect computer security.
All the signals are opto-isolated which can protect your computer security.
5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc.
Wide input voltage range: 12-24V, and with anti-reverse function.
One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
Output 0-10V analog voltage for inverter to control the spindle speed.
Electrical properties (ambient temperature Tj = 25C pm):